TPMS Reset: BMW 4 Series Tire Pressure Monitor Light (F32 G22)
Last Updated on January 26, 2021 by Nick
TPMS Reset: BMW 4 Series Tire Pressure Monitor Light (F32 G22) – The BMW 4 Series (F32) is a mid-range car from the German car manufacturer BMW. The 4 Series was presented in 2013 based on the sixth generation BMW 3 Series.
The BMW 4 Series was introduced in 2013 as a new model to replace the coupe and convertible versions of the 3 Series. Under the skin, it is still largely a 3 series and is on the same platform. However, the car is longer, lower, and wider than its predecessor.
Table of Contents
TPMS Reset: BMW 4 Series Tire Pressure Monitor Light (F32 G22)
Each time a tire pressure has been adjusted or change the tire, you need to reset the Tire Pressure Monitor (TPM). Depending on your vehicle model, here are a few ways to reset the TPM on 2014 2015 2016 2017 2018 2019 2020 2021 BMW 4 Series:
2014-2020 (F32 F33 F36)
This is the first generation of the BMW 4 Series and has several versions such as 428i 435i 440i 418d 430d 420d. In this generation, you can reset tire pressure by accessing the iDrive menu. Depending on your vehicle model, here’s how to do it:
With iDrive 1
Time needed: 7 minutes
Follow these steps if your vehicle’s iDrive looks like this:
- Stop the vehicle
Turn off the engine and shift to neutral position or P position
- Adjust the cold tire pressure in all four tires recommended on the tire placard
The tire placard located on the door panel
- Press MENU button to enter the main menu
The button located on the center console
- Go to the VEHICLE INFO
Use the dial navigation button to scroll the menu
- Select VEHICLE STATUS
Some menus will appear on the screen
- Select Tire RESET
A confirmation message will appear
- Starting the engine
Put the key into the ignition slot, depress the brake pedal, and then press the START/STOP ENGINE button
- Select PERFORM RESET to execute the tire pressure reset
You can choose cancel to cancel it
- Drive the car
The system reset is completed while the car is on the move
With iDrive 2
- Make sure to adjust the tire pressure recommended on the tire placard
- Turn on the ignition without starting the engine
- Press the MENU button to enter the main menu
- Go to the MY VEHICLE by using the Drive controller
- Select VEHICLE STATUS
- Select TIRE PRESSURE MONITOR
- Start the engine but don’t drive your car
- Select PERFORM RESET to start the initialization
- Drive the car
2020-2021 (G22 G23 G26)
Just like the previous generation, you can access the tire pressure menu to reset the TPM via iDrive on the 420d 430d 420i 430i M440i model. Here’s how to do it:
- Make sure to adjust the tire pressure recommended on the tire placard
- Turn on the ignition without starting the engine
- Press the HOME button to enter the main menu
- Go to the CAR by using the iDrive controller
- Select VEHICLE STATUS
- Select FLAT TIRE MONITOR
- Start the engine but don’t drive your car
- Select PERFORM RESET to start the initialization
- Drive the car
The TPM calibration process will complete during driving. It will finish automatically.
These instructions are based on the BMW 4 Series owner’s manual. This procedure should apply to the first and second generations of the BMW 4 Series (2014 2015 2016 2017 2018 2019 2020 2021 model years). Hopefully, the article TPMS Reset: BMW 4 Series Tire Pressure Monitor Light (F32 G22) can solve your problem. Good Luck!
About The Author
Nick
Hi! Greetings, I'm Nick, an automotive technician and a vehicle enthusiast with over a decade of experience working at a dealer service station. I have extensive knowledge of engine oils and lubricants and have helped countless customers maintain their vehicles. As an editor and author of articles on automobiles, I draw on my personal experience and professional training to provide readers with accurate and reliable information. I am passionate about sharing my expertise with others and helping them make informed decisions about their vehicles.