Hey friends, how’s life. This time I want to talk about how to reset the oil service light on the Mitsubishi Outlander. It’s one of those things that you’re going to do more often than pretty much anything else. So it’s a good idea to kind of know what’s going on, how to do it, and maybe some things along the way that you should probably pay attention to.
So when you see the routine maintenance required minder on your display, this informs you that a periodic inspection is due. This indicator will appear shortly after the vehicle is started and will automatically disappear. However, it will continue to occur when the car is started until a limit or a reset is done. So let’s move on to reset it.
Table of Contents
Time needed: 3 minutes
All right, this is a guide showing you how to reset your service light or the periodic inspection light on the old Mitsubishi Outlander (2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015). So you have a need to do is:
Make sure the vehicle is completely stopped
With the ignition off you scroll through the INFO button here until you get to the spanner icon
After that, press and hold that button to make the spanner flash
Next, you need to press the INFO button again and you’ll see CLEAR come up on the dash
Start the engine to verify the indicator has been reset
In this section, I’m gonna show you how to reset the Routine Maintenance Required warning light right now, this is for 2016, 2017, 2018, 2019, and 2020 Mitsubishi Outlander models. So now all you need to do is:
Alright guys I got a 2022 Mitsubishi Outlander and just change the oil in it. And now I want to show you guys how to reset the Engine Oil Service Due reminder that pops up on the screen. So let’s go ahead.
The engine will have problems if the oil isn’t changed. At some time, you’ll have an issue with the oil. Engine failure may be caused by using subpar oil. A common issue is burning smells.
This has to be addressed immediately, or the automobile may explode. It’s possible that you’ll get poor gas mileage. The engine may make a knocking noise.
This car runs on a full synthetic oil type, SAE 0W-20. As a more ecologically friendly choice, this viscosity of oil performs remarkably well at maximizing fuel efficiency.
There are two engine options for the Mitsubishi Outlander based on trim level. The Outlander’s 3-liter and 2.4-liter engines each hold 4.5-4.9 quarts of engine oil.
Mitsubishi’s recommended oil change interval is 7,500 miles or six months. Depending on your driving habits, if you drive a lot, you may need to get your car serviced more often. So you should do routine oil checks.
This car’s oil change costs $110 to $140. You may save $40 to $60 by changing it yourself.
High-quality oil will ensure a smooth engine operation. The Castrol Edge, Kendall, Valvoline SynPower, and Pennzoil Platinum are among prominent 0W-20 products.
So that is how you reset the service warning indicator in your Mitsubishi Outlander. I hope you enjoyed this article and you found it helpful. If you did, please share and comment. See you at the next one; thanks for reading!
Hey everyone! Today, I'll show you how to reset the Oil Maintenance Light on a…
Hey there, everyone! Today, I'll be showing you how to reset the oil change light…
What's up, everyone? If you're an Alfa Romeo Giulia owner, you know that keeping your…
Hey what's up Bimmers! Owning a BMW M8 comes with the responsibility of proper maintenance,…
Greetings, fellow Bimmer lovers! Today, we have an exciting topic to delve into: how to…
What's up Bimmer! Welcome to our guide on resetting the oil service light on your…
This website uses cookies.
View Comments
This does not work on my 2015 Outlander.
After finally finding it in the vehicle manual, the ignition has to be off for this to work...not on or in acc. Hope that helps. FYI - for a 2015 Outlander service message reset.
Mine will beep but won't say clear after the wrench is flashing. Ignition is all the way off. I tried it running, acc, and totally off. Any ideas?
When the wrench is flashing release the info button and then hold it down again. Also ensure the engine is not running.
Thank you very much for the correct information.
I've tried this several times and it never says "clear" it always says "NAS 10." Why???? It's driving me crazy.
did you ever figure it out, i;m trying and it's not working for me... driveing me nits ... LOL